27.08.2026 · 4 min read · Atakaş Technical Team

Choosing Hollow Sections: Wall Thickness and Size for Each Project

How to read a hollow section size, what wall thickness really changes, weights per metre for common sizes, and section choice from railings to steel frames.

Choosing Hollow Sections: Wall Thickness and Size for Each Project

Hollow sections are among the most versatile products in fabrication: they appear in railings, greenhouse frames, racking systems and steel structures alike. That versatility creates a problem of its own — with so many options it is easy to pick the wrong section. The decision really comes down to two numbers: outside dimension and wall thickness.

How to read the size

A hollow section size is written as a × b × t: the first two values are the outside dimensions and the third is the wall thickness. For example 40 × 40 × 2 describes a square section of 40 mm outside size with a 2 mm wall. For rectangular sections the first figure is usually the depth: 100 × 50 × 3.

For structural use, products fall under EN 10219 (cold formed hollow sections); where precise dimensions and surface quality are needed for mechanical applications, EN 10305-5 is specified instead. Material grade is most often stated as S235JRH or S355J2H.

What does wall thickness change?

  • Stiffness and capacity: bending resistance is far more sensitive to outside dimension. At the same weight, a 60 × 60 × 2 section is clearly stiffer than 40 × 40 × 3. In other words, going bigger usually beats going thicker.
  • Welding: below 1.5 mm the risk of burn-through rises and TIG or pulsed MIG is preferred. Walls of 2 mm and above weld comfortably with standard MIG/MAG.
  • Surface treatment: sections destined for hot-dip galvanizing can distort below 2 mm; galvanizers usually set a minimum wall thickness.
  • Cost: since price is per kilogram, wall thickness is cost. Specifying 1 mm more than needed can raise project tonnage by up to 30%.

Common sections and weights per metre

Section (mm)Approx. kg/mTypical use
20 × 20 × 1.50.87Furniture, light frames, signage
30 × 30 × 2.01.76Railing posts, greenhouse frames
40 × 40 × 2.02.39Fence posts, light racking, bench legs
40 × 40 × 3.03.49Loaded frames, door frames
50 × 50 × 3.04.43Platform frames, machine chassis
60 × 60 × 3.05.37Light steel structures, ceiling supports
80 × 80 × 4.09.55Columns and beams, canopy supports
100 × 100 × 4.012.06Steel structure columns
100 × 50 × 3.06.78Beams loaded in one direction
120 × 120 × 5.018.06Heavy columns, crane legs

The values above are theoretical weights calculated without corner radii; manufacturer tables may show figures 1–3% lower.

Which section for which project?

  1. Balcony and stair railings: 40 × 40 × 2 for posts and 30 × 30 × 2 for horizontal members suits most applications.
  2. Greenhouses and agricultural buildings: 40 × 40 × 2 or 50 × 50 × 2; galvanized sections should be preferred for outdoor exposure.
  3. Racking and storage: 60 × 60 × 3 and above for loaded uprights, with increased thickness at connection points.
  4. Machine chassis: where vibration is present, enlarging the section works better than thickening the wall: 60 × 60 × 3 or 80 × 80 × 3.
  5. Steel structures: 100 × 100 × 4 and above for columns; section and grade must always follow the structural calculation.

Pre-order checklist

  • Section and wall thickness: write them clearly as a × b × t.
  • Grade: S235JRH or S355J2H; is the standard EN 10219 or EN 10305-5?
  • Surface: black or galvanized; will it be painted after galvanizing?
  • Length: standard 6 m or project length?
  • Tonnage: verify total weight as pieces × length × kg/m.

Weld preparation and corner radius

The corners of a hollow section carry a radius created by cold forming, typically 1.5 to 2.5 times the wall thickness. When two sections meet at a corner, that radius prevents a fully contacting joint and calls for a fillet weld. On precise assemblies, asking for the corner radius at order stage makes jig and fixture design much easier.

Cold-formed corners are also the most work-hardened region of the material. Avoid drilling or re-bending in that zone; place connection holes on the flat faces and run weld seams along the flat edge rather than the corner.

See the size ranges on our hollow section and industrial pipe pages, and calculate total tonnage instantly by entering your section and quantity in our weight calculator.

Back to all articles